Home > Windows 98 > Windows 98 Second Edition Shutdown Supplement

Windows 98 Second Edition Shutdown Supplement

Contents

Had a problem with Scandisk also, after I installed firewall software. It STILL doesn't shutdown properly! See http://support.microsoft.com/support/kb/articles/q196/0/08.asp for details on a supported fix that corrects this problem. Test Windows shut down. http://internetpasswordpro.com/windows-98/windows-98-second-edition-iso.html

To do this, follow these steps: Click Start, point to Settings, click Control Panel, and then double-click System. Click OK until you return to Control Panel. Detailed instructions for troubleshooting these items are not given in the present article; if you do not know how to test these steps, please seek help in the online peer support You can safely attach a serial mouse now. https://support.microsoft.com/en-us/help/238096/problems-shutting-down-windows-98-second-edition

Windows 98 Second Edition Shutdown Supplement

Flag Permalink This was helpful (0) Collapse - It could be hanging on by TONI H / January 22, 2005 1:04 AM PST In reply to: Win98SE freezes at shutdown screen Shutdown problems in Windows 98 Second Edition can be caused by any of the following: A video card that is not assigned an IRQ in real mode. WIN98 SE NOTE: This box does not exist in Win98 SE.

Do you have enough space on your computer to install into a new folder?A. Restore the file from your Windows disk or wherever you obtained it and then test Windows shut down. Microsoft reports that the most commonly reported threshold for this problem is eight (8) mapped network drives. in Device Manager/System Settings/PCI Bus Properties, set Device Enumeration to BIOS and turn off IRQ steering. (These settings pretend that Win 98 SE is not a PnP operating system.) (8) Clayton

Clear the checkmark from the last box, "Get IRQ Table From Real Mode PCIBIOS 2.1 Call." (7) Bill Snyder has reported that the shutdown problem in SE, as well as several Windows 98 Shutdown Command For information about how to do so, contact your BIOS manufacturer. After each program is restored, test Windows shut down. http://www.infocellar.com/software/shutdown-problems-win98se.htm METHOD 2: Maintain each user's temporary Internet files in the user's Home directory.

If the system hangs, go to STEP SIX. If Windows still hangs during the shutdown process after you reinstall it, your computer may have faulty hardware or faulty system components including RAM, the CPU, the motherboard, or an internal If you install into a new folder, apply the Windows 98 Second Edition Shutdown Supplement as referenced in this article, and you still experience problems shutting down, check with your hardware FOR ALL VERSIONS OF WINDOWS: Test Windows shutdown.

Windows 98 Shutdown Command

This includes disabling any TSRs loading in real-mode, disabling programs that start from your Startup group, and disabling any non-essential 3rd-party device drivers. useful reference If this happens frequently and the software is an application, try reinstalling the application. Windows 98 Second Edition Shutdown Supplement THIRTEENTH STEP: USE BOOTLOG.TXT TO IDENTIFY THE PROBLEM If Windows still hangs during the shutdown process, create a BOOTLOG.TXT file by restarting the computer, bringing up the Boot Menu and selecting Double-click any device, then click the Test Configuration check box to clear it.

Restart the computer. get redirected here These programs, which run in the background, will often cause problems. Often (but not always) a clue will be that the floppy drive light comes on during shutdown. Click the Hardware Profiles tab.

After you restart the computer, attempt to shut down your computer again. For information about how to disable PCI bus IRQ Steering, click the article number below to view the article Click the RunServices folder. 4. This state of affairs will allow the VCache to grow very large. navigate to this website You may need to install updated drivers for these devices.

Known Issues IRQ Steering: This option allows several PCI devices to share the same interrupt request (IRQ). These issues include computers restarting when shut down and computers hanging on shutdown. Microsoft identified this problem in Knowledge Base article 200692, advising that you contact Compaq for a solution, or simply disabled the software.

wrote: “Your network connection doesn't allow you to shut down, therefore unloading the driver results in a lockup of the system, or there are other drivers or programs that are hanging

NINTH STEP: RULE OUT EMM386-RELATED MEMORY CONFLICTS A memory conflict sometimes exists when Emm386.exe is not loaded from the CONFIG.SYS file. If a clean-boot resolves the issue, you can then use the System Configuration Utility tool to determine the program that is the cause of the shutdown problem. This may take some time to run. If you have Windows Millennium (ME) the procedure is a little different.

Windows 98 There are several reasons that can cause the computer not to shutdown to the "It's now safe to turn off your computer" message. METHOD 3: Maintain all users' temporary Internet files in a shared common folder. Click OK, click OK, and then restart your computer. http://internetpasswordpro.com/windows-98/windows-98-client-using-windows-server-2000.html If your computer locks you might be able to use [Ctrl] [Alt] [Delete] to close programs and unfreeze Windows (If you don't know how to use this feature see section 2w

Whichever process you choose to disable, reboot the computer to set your new configuration. (Return to TOC) 7w. FOURTEENTH STEP: OTHER SOLUTIONS (1) The PC Speaker driver (SPEAKER.DRV) can cause Windows to stop responding at shutdown or startup. Place a semicolon (;) at the beginning of each line that begins with DEVICE= and ends with .386. Perform the following steps to keep the virus scan software from scanning your floppy drive on shutdown: When running McAfee AntiVirus: Right-click the McAfee icon located in the system tray (icons

If the system doesn't hang, rename the files and proceed with these steps: Restart Windows and bring up the Boot Menu. These entries are located at the end of the file and may provide clues as to the cause of the problem. Each Terminate= entry should have a matching EndTerminate= entry on a successful shutdown. For step-by-step help figuring out why SE won't shut down, see How to Troubleshoot Windows 98 Second Edition Shutdown Problems.

Removing "Log Off" It's not a bug but it can be annoying. Make sure "Never use the numeric data processor" is NOT selected at the bottom.