Home > Windows 2000 > Windows 2000 Routing HELP!

Windows 2000 Routing HELP!

To add static routes, use the following format: Route add < subnet > mask < netmask > < gateway > metric < metric > if < interface > The following is Step 1: Open up the start menu, and click Run. A dialog box will appear reporting that you’ve started the R&R wizard. Step 2: Type command in the Open: box, and click Okay. http://internetpasswordpro.com/windows-2000/windows-2000-iso.html

Windows95/98/ME is able to work as a router using a registry entry( NOT supported by Microsoft ) :HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\VxD\MSTCP : "EnableRouting", value "1" Windows NT4 Workstation and Serverfully support IP routing:it is print Prints a route or routes. Persistent routes are stored in the registry location HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\PersistentRoutes. The following table lists valid commands. http://www.windowsnetworking.com/articles-tutorials/windows-2000/w2kprout.html

All rights reserved. To see the route table for your computer, at the command prompt type route print . The following sections describe the columns shown in the Active Routes section of the net print command.

Go ahead and right click the network connection again and then click enable. When the mask is written in binary, a 1 indicates a bit that must match and a 0 indicates a bit that does not have to match. This is where our naming convention pays off. If something goes wrong you can always change the settings back to what they were!

Comments Facebook Linkedin Twitter More Email Print Reddit Delicious Digg Pinterest Stumbleupon Google Plus Powered by Livefyre Add your Comment Editor's Picks Google Fiber 2.0 targets where it will stage its Network Configuration and Management TCP/IP in Windows 2000 Professional Configure Local IP Routing Table Configure Local IP Routing Table Manually Edit the Route Table Manually Edit the Route Table Manually Edit However, I think that not only is this a good large network solution, but it is also a good SOHO business solution as well. http://www.techrepublic.com/article/routing-and-remote-access-on-windows-2000-advanced-server/ Top Of Page Gateway Address The gateway address is the forwarding IP address of where the packet must be sent.

The -p parameter is only supported on the route command for Windows NT 4.0, Windows 2000, Windows Millennium Edition, and Windows XP. Click Next to continue.Figure2Click Configure And Enable Routing And Remote Access.On the next screen, you will see the connection choices. The naming convention is entirely up to you, but I recommend using names that will allow you to quickly recognize which NIC is serving what purpose. If the R&R module is up and running, a green arrow pointing upward will appear.In order to configure the R&R module correctly, you must have your DNS server and DHCP server

Therefore, the integration of routing (which includes demand-dial routing) and remote access was done to leverage the existing PPP client/server infrastructure that existed for the remote access components. https://technet.microsoft.com/en-us/library/cc977249.aspx TechNet Archive Windows XP Command-line reference A-Z Command-line reference A-Z Route Route Route Arp Assoc At Atmadm Attrib Using batch files Bootcfg Break Cacls Call Chcp Chdir (Cd) Chkdsk Chkntfs Cipher To do this in regedit.exe, right-click the entry, and then click Modify.In regedt32.exe, click on the wanted entry, click on Edit, and then click on the appropriate menu choice. 6.Close the This is the route to which the computer sends IP packets when the other route entries do not specify where to send them.

If the command is print or delete, the Gateway parameter can be omitted and wildcards can be used for the destination and gateway. http://internetpasswordpro.com/windows-2000/windows-2000-and-pop-ups.html Did the page load quickly? Automatic determination of the interface metric, enabled by default, determines the speed of each interface and adjusts the metrics of routes for each interface so that the fastest interface creates the Windows 2000 Server provides an easy way to configure the router.

Layer Two Tunneling Protocol (L2TP) over IP Security (IPSec) support for router-to-router VPN connections. The end user can simply plug their computer in, and their network will work. The Routing and Remote Access service works with a wide variety of hardware platforms and hundreds of network adapters; the result is a lower cost solution than many mid-range dedicated router my review here Second, you must decide what IP scheme to assign the inside card.

There is a lot of information at the following link. For hexadecimal values, precede the hexadecimal number with 0x. Did it open a webpage?

http, ping, tracert...

Open a new copy of your web browser? For locally attached subnet routes, the gateway address is the IP address assigned to the interface that is attached to the subnet. Default route (a route used when there is no other match). Verify that the TCP\IP is listed and click Next.

Then click Configure And Enable Routing And Remote Access. Privacy Policy | Cookies | Ad Choice | Terms of Use | Mobile User Agreement A ZDNet site | Visit other CBS Interactive sites: Select SiteCBS CaresCBS FilmsCBS RadioCBS.comCBS InteractiveCBSNews.comCBSSports.comChowhoundClickerCNETCollege NetworkGameSpotLast.fmMaxPrepsMetacritic.comMoneywatchmySimonRadio.comSearch.comShopper.comShowtimeTech Click okay all the way out of this menu. http://internetpasswordpro.com/windows-2000/windows-2000-nt.html Simply choose the card that is directly connected to the Internet and click Next.Figure5Specify your Internet connection NIC.The final screen, shown in Figure 6, will then appear, and we are finished.

VPN remote access (remote access over VPN connections using either PPTP or L2TP over IPSec) as either the client or server. To enable IP routing for all network connections installed and used by this computer, assign a value of 1. This documentation is archived and is not being maintained. Yes No Do you like the page design?

Did the page load quickly? The computer in this case must provide the routing information to send IP packets from one network to the next, because no router is provided to perform this task. You can use either decimal or hexadecimal values for the interface index. The ip address you choose should be very similar to the router's ip addres.

Enter the dns servers we prevoiusly found into the two DNS Server boxes. Top Of Page Netmask The netmask defines which portion of the network address must match in order for that route to be used. On-demand or persistent VPN demand-dial routing (demand-dial routing over VPN connections using either PPTP or L2TP over IPSec) as either the calling router or the answering router. Each change in the status of a route necessitates an equivalent alteration in the route table.

We have set up the Windows 2000 Advanced Server to act as a router and share our single IP to use with the rest of our network.Figure 6Click Finish to complete We'll show you how. I chose NAT, and I suggest you do the same for several reasons that I will discuss in a future article. Finally, the challenges of manually maintaining local route tables is multiplied when supporting a large number of computers in a department or enterprise.

See ASP.NET Ajax CDN Terms of Use – http://www.asp.net/ajaxlibrary/CDN.ashx. ]]> Network Utilities Intro Download Buy News Support Home List