Home > Windows 2000 > Windows 2000 Professional Freezes

Windows 2000 Professional Freezes

Anyways, I put the Celeron back inside. Slow Boot or Error Messages in Windows 2000 After Installing Roxio Easy CD Creator 5.0 Microsoft Knowledge Base Article: 298583 - Immediately after you install Roxio Easy CD Creator 5.0 Platinum, When this problem occurs, you may receive the following error message: Windows 2000 could not start because of a computer disk hardware configuration problem. WINDOWS 2000 PRO CRASHES AT STARTUP! http://internetpasswordpro.com/windows-2000/windows-2000-professional-hjt-help.html

Robocopy alternatives? It boots fine in "Safe Mode with Networking". It happened mostly when I was downloading things.I found that a 4GB hard drive was too small, so I found an 80GB hard drive and installed Windows 2000 again. How can I figure out what makes it hang? http://www.tomshardware.com/forum/215300-46-hangs-startup-2000-logo-screen

If your hardware is less than new, then you need to work down this short list and be sure you are not chasing a hardware issue.Bob Flag Permalink This was helpful All Rights ReservedAd Choices The information on Computing.Net is the opinions of its users. Proffitt Forum moderator / February 1, 2006 11:52 AM PST In reply to: Already Done! Jimmy, May 6, 2004, in forum: Microsoft Windows 2000 Networking Replies: 1 Views: 290 Robert L [MS-MVP] May 6, 2004 Windows 2000 pro and Win XP pro Ged, Jul 10, 2004,

There is no way to narrow down what caused it without other clues so it's google time for you. The symptom was that Windows 2000 Pro would usually (though not always) get stuck with 11 bars of the "Starting up..." progress bar on the low-res graphical startup screen (i.e., 11/18 Computing.Net cannot verify the validity of the statements made on this site. WINDOWS 2000 PRO CRASHES AT STARTUP!

So I thought that the original NIC must have been defective, but when I put the original NIC back in the computer, the two problems were both STILL gone. When Windows 2000 won't boot A server crash is always a nightmare. No, that one program doesn't work in Virtual PC 7 on the Mac or in VMware on Linux). https://www.cnet.com/forums/discussions/help-windows-2000-pro-crashes-at-startup-154053/ Just click the sign up button to choose a username and then you can ask your own questions on the forum.

If the Windows NT files are located on a FAT partition you can boot from a bootable MS-DOS diskette to rename the file. Comments (You may use HTML tags for style) Search About this Entry This page contains a single entry by Ask Bjørn Hansen published on December 29, 2004 2:39 AM. I downloaded the drivers from HP's website. If that doesn't work then idk what to do.

HOW TO: Replace a Driver on a Windows 2000-Based Computer That Will Not Start Microsoft Knowledge Base Article: 313670 - This step-by-step article describes how to replace a driver on a why not try these out I register my software so Microsoft knows what I have. HOW TO: Determine if it Is Possible to Start Windows 2000 with the Keyboard Unattached Microsoft Knowledge Base Article: 320466 - This step-by-step article describes the issues that are related to The most common symptom when trying to boot from the shadow drive is that the system will hang after POST with a blinking cursor and no boot menu options are displayed.

Last time it was 35 bucks.Given you can duplicate that CD, I always wonder how one gets by without a backup.Sorry, but given only what you posted, the outlook is rather http://internetpasswordpro.com/windows-2000/repair-windows-2000-professional.html Software ▼ Security and Virus Office Software PC Gaming See More... Safe Mode with Networking won't start up very many of the drivers for the in-built hardware that a laptop has. The drivers that are installed on the netbook also supports 2000 so I don't see why it shouldn't be able to run it.

Leave a comment Name Email Address URL Remember personal info? You'll be able to ask any tech support questions, or chat with the community and help others. It was barely warm. my review here Your computer may also restart automatically.

Report • #5 OtheHill April 23, 2014 at 05:38:29 Read the link below for a possible solution.http://support.microsoft.com/kb/305098 Report • #6 thomasad May 18, 2014 at 16:16:55 Could it be that the All submitted content is subject to our Terms of Use. It makes a big difference when I have to make the call.

Off-Topic Tags How-tos Drivers Ask a Question Computing.NetForumsWindows 2000Software Problems Windows 2000 Randomly Hangs Tags:compaqFreezePresarioCrash LOLZpersonok May 9, 2013 at 17:30:03 Specs: Windows 2000 Professional, Intel Celeron 850MHz I have a

In-built modems are very often the culprit in a case like this, since they're often exposed to over-voltage conditions because of accidentally plugging into digital phone system or power surges coming If I take the hard drive out of the netbook and try to boot off of the usb drive I get the same error. Eventually, I discovered that Windows 2000 would resume booting if I briefly pressed the power button on the system unit. Ever since I hooked it up to the netbook I get that error.

This is not unlike you some hundred miles from home and no spare tire and you get a flat. by R. Entire contents © 1999-2003 LabMice.net and TechTarget All rights reserved This site and its contents are Copyright 1999-2003 by LabMice.net. http://internetpasswordpro.com/windows-2000/how-to-install-windows-2000-professional.html Windows Does Not Start After PcAnywhere 9.0 Installation Microsoft Knowledge Base Article: 317051 - When you restart your computer after you install Symantec pcAnywhere 9.0, you may receive the following error

by the_real_martian / February 4, 2006 11:44 PM PST In reply to: Or you have a reciept, box, CDKEYS, etc. I have checked the hardware; it's fine. Yes, I see the irony, go away. 2 Comments trashtalker#1 | December 30, 2004 12:58 PM | Reply well there's your problem...you're installing Windows. Source: Windows & .NET Magazine (Nov. 1999) Repairing the Master Boot Record One of the most important parts of your system's hard disk is the Master Boot Record (MBR).

Could not read from selected boot disk. Start by disabling devices that you don't need for your application (especially built-in modems, sound cards, etc.). If the System hive is full, you may not be able to start your computer Cannot Start Windows NT 4.0 After Installing Previous Version Microsoft Knowledge Base Article: 155119 - If An error (403 Forbidden) has occurred in response to this request.

I REALLY like Windows 2000, and I don't want to lose it. If the computer is allowed to sit for two hours or longer, the boot process may finish. I had the machine plugged into my LAN hub, and from there to a rock-solid, very fast, cablemodem-based internet connection, and this machine could surf the web pretty well, but it