Home > Windows 2000 > Windows 2000. How Do I Get To The Startup List

Windows 2000. How Do I Get To The Startup List

To do this click: Start Menu > Run And then type: "services.msc". This is one of the last phases of Setup and involves the registration of OLE control dynamic-link libraries (DLLs). Note: Some adapters (for example, some video adapters) run their POST sequence before the memory and device check, which runs during the initial POST. Partitions and formats the drive for the file system or converts to an NTFS file system when you upgrade from Windows NT 4.0 Workstation. navigate to this website

You need to install the systems in the following order: MS-DOS Windows 95 or Windows 98 Windows NT Windows 2000 Professional If you are already running a multiple-boot system with Windows If it is needed it cannot be started either until you set the Startup Type to Automatic/Manual & Reboot, or Start the service. Logical Disk Manager. Set this to Manual. this contact form

Indexes contents & properties of files on local & remote computers; provides rapid access to files through flexible querying language. Review the procedures and considerations for setting up a multiple-boot configuration. Follow the steps below for instructions on how to remove programs from the win.ini file.

The two of interest to us, called Shell and Userinit, specify the default Windows shell and the user shell, respectively. Creating the Startup Disks To prepare for a system failure on a computer that you cannot start from the operating system CD, you need to create floppy disks that can start All devices are configured by the BIOS If Enable Plug and Play operating system is disabled and the device has a static configuration, you can not remove the device without turning Install service packs with Windows 2000 Professional.

Otherwise, set it to Manual. Removing Windows 2000 Professional Files Caution: Make sure you back up all important data before removing the Windows 2000 files from the computer. Provides network connections & communications. Then when you view the contents of startup in MSCONFIG press the PrintScreen key on the top right corner of the keyboard (on some systems it only works if you also

You can edit the time-out and default parameters in Boot.ini by using the System option in Control Panel. If you have only one hardware profile, Windows 2000 Professional uses the default settings. In Advanced properties, make sure that "Stop the task if it runs > " tickbox is unticked. 2) Create a service. The Plug and Play Manager gathers information about the new device and begins configuring the device.

The dependencies are described in the DependOnGroup and DependOnService entries in the subkey HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\DriverName. Note: Windows 2000 startup is not considered complete until a user successfully logs on to the system. https://forums.anandtech.com/threads/windows-2000-disable-startup-programs.396945/ The remaining IRQs can be used by expansion cards that are added to the computer. Much like Task Scheduler in Windows 98 this can be used to schedule certain programs be to run at specified times & such. In order to change the Startup type of a Service enter the Properties of the respective Service.

If you are connected to a Windows 2000 Domain set this to Automatic. useful reference If your computer has lots of memory, you might not notice too much of a startup delay. The Plug and Play Manager determines that this action would cause the USB hub, the joystick, and the camera to become unplugged. Select the Value data field.

Nirmal Sharma, a Microsoft Most Valuable Professional (MVP) has written a Community Solutions KB article concerning this issue and how you can fix it by remotely connecting to the affected machine's You can usually isolate these failures to one of the following locations: Device detection. I find only two programs listed here, Windows Messenger (which I want to start up whenever Windows starts) and ctfmon.exe, which ProcessLibrary.com tells me has to do with the Microsoft Office http://internetpasswordpro.com/windows-2000/windows-2000-startup-very-slow.html Manages device installation & configuration & notifies programs of device changes.

In this field set the number of days after which you wish the Failure count to be reset. When the status bar completes, Ntoskrnl prepares the network information. Click the Start Menu Programs tab, click the Advanced button, click the Programs folder, and then click the Startup folder.

Begin by logging on as Administrator.

Click Ok 3 times to exit Network & Dial-up Connections. If you do happen to use a smart card system set this to Automatic. Now, onto the Services themselves; Alerter. To do so, Right click on the Service in question, select Properties, then the Recovery tab.

This can increase boot time, although will save resources as the Service need not be requested to Start when Windows 2000 is loaded. These files perform initial hardware detection and then pass control to the kernel, which is loaded along with the boot drivers and the drivers for the hard drive controller(s). The system partition must be on the first physical disk and contain the system startup files listed in Table 6.1. http://internetpasswordpro.com/windows-2000/windows-2000-hangs-on-startup.html OC Manager.

But a lot of applications start up programs or services when they really aren't needed, and those are the culprits you probably want to ferret out and eliminate. Windows 2000 Professional Understanding the various phases of Setup and Startup The Phases of Setup The following will provide you with a brief description of how boot drivers and Plug and Although it’s highly unlikely you’ll need this, you never know. In the Task Manager window, click the Startup tab.

Although if you are using a modem to provide Internet connectivity it is recommended you set this to Automatic (Personally I've not found this to be the case however).