Home > Win 2k > Win 2K On RAID 0

Win 2K On RAID 0

This article also explains some of the advantages and disadvantages of the various RAID configurations. Sizing Your NT RAID Array Know how to troubleshoot bottlenecks in your disk subsystem, and you This will make the install go with ACPI disabled. RAID 0 setups are standard on high-end gaming PCs and graphic design workstations, and provide a measurable, albeit modest performance boost for hard-disk-intensive programs.RAID 1 (Mirroring): A RAID 1 setup protects But the thing is he has this set up as a Raid with 2 hard drives.

ForumsJoin Search similar:[WIN7] Messed up RAID; How to fix? It will tell you. To extend an NTFS volume, complete the following steps: In Disk Management, right-click the simple or spanned volume that you want to extend, and then select Extend Volume. If any of the drives in the stripe set fails, the parity information is used to recover the data. (This process, called regenerating the striped set, is covered in the section http://www.tomshardware.com/forum/1307-46-win2k-raid-setup

To correct this problem, you need to replace the failed drive and then use an emergency boot disk* for the system or a similarly configured system to enable system boot. You'll know that a stripe set with parity drive has failed because the status of the set changes to Failed Redundancy and the status of the individual volume changes to Missing, With 2 drives acting as one the cache is doubled!

If you elect to format the volume, follow the steps described in the section of Chapter 10 entitled "Formatting Partitions." Figure 11-4: Format a volume by specifying its file system type File system As with partitions, each volume can have a different file system type, such as FAT (file allocation table), FAT 32, or NTFS (Windows NT file system). When i made the disk of ICH7 I was able to get past the installation and actually install windows, the only backdraw with that was that i was stuck with a You should be prompted to press F6. #5 SpunkyJones, Jun 9, 2004 BigDog Member Joined: Dec 27, 1999 Messages: 121 Likes Received: 0 I installed the SATA RAID driver from

When 48-bit LBA support is turned on for ATA Packet Interface (ATAPI) drives in a RAID 1 (mirroring) configuration, performance is noticeably reduced. I did not install the plain SATA driver. #6 BigDog, Jun 9, 2004 jbritt1234 Senior member Joined: Aug 20, 2002 Messages: 406 Likes Received: 0 You installed them at the Data written to the stripe set is broken into blocks that are called stripes. view publisher site This is not necessary with Windows software RAID 0, however, it's far faster than letting Windows re-sync (copy the data to) the mirror in the background.Transferring an existing operating system is

RAID 1 offers no gain in performance and effectively reduces available capacity by half -- two 2TB drives provide only 2TB of storage.RAID 5 (Distributed Parity): Though you get both faster Click Next and then click Finish. IOT reaches new climax [Security] by Snowy278. The following step is to launch RAID partition software - EaseUS Partition Master Server Edition and use its built-inresize and movefunction to extend this RAID with the unallocated space.

Windows setup sees the raid drive .... When using a RAID, you don't see icons for each one of the disks on the desktop but rather a single icon that represents the array. And you can't extend simple or spanned volumes that were upgraded from basic disks. Right-click the failed volume and then select Remove Volume.

You use this parity sector to recover data in case of hard drive failure. Windows 7 Home allows JBOD and RAID 1 while Professional and Ultimate add RAID 0 mirroring. You can mirror individual partitions, including partitions from different drives onto a single drive.The disadvantages are that other operating systems, such as the Linux used on repair discs, can't see Windows set to ?Hard Disk?

All data on the removed mirror is deleted. Windows 2000 Professional also has JBOD, 0, and 1. You can assign a drive letter or path later, if necessary. If one drive fails, there's no data loss because the other drive contains the data. (Doesn't include disk striping.) Redundancy.

RAID 1+0, 0+1, 10: Some adapters combine (referred to as nesting) RAID 0 and RAID 1 to provide both data redundancy and increased disk performance. b) "Onchip Serial ATA? Thankfully, this incredibly annoying limitation of Windows XP doesn't apply in Windows Vista and Windows 7 which can read drivers from hard drives, flash drives, or optical media.Tools: You'll need a

Elizabeth M.

You can also break the mirror. First thing, you need to figure out what you're working with before you can start installing stuff. Windows 2000 supports RAID levels 0, 1, and 5. It's largely irrelevant given today's more capacious hard drives.RAID 0 (Striping): This setup increases hard-drive performance by splitting, or striping, data across two drives.

my god im going crazy 0 primesuspect Beepin n' Boopin Detroit, MI Icrontian Apr 2006 edited Apr 2006 Okay, with only two drives, you cannot install windows on one of them Right-click the original system volume, and then select Add Mirror. Related: Storage Network Storage Cloud & Services PCs Hard Drives Input Devices 1 2 Page 1 Next You Might Like Shop Tech Products at Amazon PCWorld PCWorld helps you navigate the I have many options but since its Win2k I basically only have 2 options: Make Intel ICH7 32 bit RAID Driver Disk Make Silicon Image 32 bit RAID Driver Disk.

Repairing a Stripe Set Without Parity A stripe set without parity doesn't have fault tolerance. This is probably a stupid question considering Microsoft?s help files state that ?Mirrored and RAID-5 volumes are available only on computers running Windows 2000 Server?. How to select a RAID disk array RAID can be a confusing technology to master. What mobo do you have? #7 jbritt1234, Jun 9, 2004 BigDog Member Joined: Dec 27, 1999 Messages: 121 Likes Received: 0 Yes ...