Home > Win 2000 > Win 2000 Pro Freezes When Loaded Up

Win 2000 Pro Freezes When Loaded Up

when i boot now tho it seems to take forever. it repaired windows (to my knowledge) since it said it was finished and put on a count down to restart. Privacy Policy Terms and Rules Help Connect With Us Log-in Register Contact Us Forum software by XenForo™ ©2010-2017 XenForo Ltd. it said "unregmp2.exe - entry poinjt not found. check my blog

At the Welcome to Setup screen, press R to start the Recovery Console. Your visitors may find it useful too and appreciate that! The processI detail is reversible if you back up the original hives first as instructed so it is worth a try ;) The fundementals of this procedure should also workon Windows No, that one program doesn't work in Virtual PC 7 on the Mac or in VMware on Linux). http://www.tomshardware.com/forum/215300-46-hangs-startup-2000-logo-screen

The symptom was that Windows 2000 Pro would usually (though not always) get stuck with 11 bars of the "Starting up..." progress bar on the low-res graphical startup screen (i.e., 11/18 When the installation completed, it >> >> You did check the Roxio site (or who ever the current owner of Roxio >> is)? >> > >Yes. There are a number of issues that can cause a system to fail to boot, and we've tried to list as many as we could find here.

its a new mobo put into an existing comp. Here is a link to a Phoenix and Award BIOS FAQ that provides additional BIOS related information and troubleshooting steps If your system is overclocked, Try reverting to the original standard http://support.microsoft.com/?kbid=820759 - Similar pages Searching MS was mentioned earlier, when 2 URLs were posted. It's the 1st one you are talking about? >Now I can't boot into anything, including flavors of safe mode, or the >last known good configuration.

This article describes how to perform clean-boot troubleshooting to determine if the problem in question is with the core operating system or with a program loading in the Windows environment. I run the Internet Connection Wizrd and try to install a new connection. Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More... https://www.neowin.net/forum/topic/380442-windows-2000-hangs-on-boot/ Yes, I see the irony, go away. 2 Comments trashtalker#1 | December 30, 2004 12:58 PM | Reply well there's your problem...you're installing Windows.

IBM typically uses F1 or F2. Hence, my deciding to uninstall then reinstall. > >> >said I needed to reboot my machine. And the problem is that, with >multiple USB devices plugged in, the Windows splash screen progress bar >freezes at the 12th blue segment. Like I said before after you get it up and save all your inportant stuff do a clean install.

Then... https://arstechnica.com/civis/viewtopic.php?f=17&t=769037 You need to install Linux or something. ;-) Seriously, have you tried wine? to handle the request The network provider then fulfills the request by accessing the remote resource and passing the data back to notepad via the I/O Manager I have greatly simplified HOW TO: Troubleshoot Startup Problems in Windows 2000 Microsoft Knowledge Base Article: 315396 - This article describes general procedures that you can use to troubleshoot startup problems in Windows 2000.

Help! click site This will allow you to temporarily boot from a CDROM. Happy and successful troubleshooting! Start a new discussion instead.

The problems referred to persisted after I'd updated the software >from the Roxio web site. I get to 12 blue blocks on the progress >bar, and then it hangs. If chkdsk fails to resolve the problem, at this point you may need to reinstall windows but first ... news The problems referred to persisted after I'd updated the software from the Roxio web site.

With the Windows XP CD-ROM still in the CD-ROM drive or DVD-ROM drive, type the following commands, pressing ENTER after each command: cd system32 ren msdart.dll msdart.old CD-ROM_or_DVD-ROM_Drive_Letter: cd \i386 expand You can find more information about disk utilities here: http://www.techspot.com/community/topics/drive-diagnostic-utilities-compendium.7602/ Memory can also cause these problems. Note that this is not possible on all computers because of specific firmware restrictions in the Basic Input/Output System (BIOS).

The windows OS is looking in the registry, executing PnP (Plug and pray) and ACPI routines checking the components and resources found.

When booting windows XP in safe mode the last driver that shows loaded is mup.sys. I can't wait for winxp sp2 to be released, so that I can slipstream my CD and avoid the large update requirements. Yes, my password is: Forgot your password? Please be thoughtful, detailed and courteous, and be sure to adhere to our posting rules.

There is some minor HD activity with maybe 3 or 4 blips. i got the same error in my desktop. Booted fine. > >I then plugged in the speakers. More about the author Follow these techniques to track down the source of the problem and get back online as soon as possible.

Unbold have been added ... It worked and all my files are there! Shut down Windows, plugged in the card reader, the computer detected the new hardware, and everything started fine and the card reader worked. If your computer shuts off and won't even post the bios, look at your power supply it my be at it's limit.

Safe Mode with Networking won't start up very many of the drivers for the in-built hardware that a laptop has. The next screen is a white, graphical screen which says, Windows 2000 Pro; at the bottom it says, "Starting Up", and there is a series of bars. Yes, my password is: Forgot your password? Each BIOS is different, but here is an example: Oct 20, 2003 #2 Phantasm66 TS Rookie Posts: 5,734 +7 Well done, my dark apprentice....

Enjoy! You will be asked to repair an existing XP installation or install a fresh copy of Windows XP/2000. The only one that it selects is connect using a broadband connection. MeredithClick to expand...

All the best to you.