Home > How To > How To Connect Ide Dvd Drive To Sata Motherboard

How To Connect Ide Dvd Drive To Sata Motherboard

Contents

In almost all cases, you will want to work with the bottom window. It includes instructions for both SATA and IDE types. The gray connector attaches to the secondary, or slave, drive. On the next screen select Primary, Extended or a Logical Partition and click Next to continue. weblink

You can route cables to a pair of extra SATA ports on the motherboard, but that has a drawback or two.Research led me to this adapter, along with anLG Electronics Optical Something we hope you'll especially enjoy: FBA items qualify for FREE Shipping and . Back HDE® SATA to IDE/IDE to SATA Drive Interface Adapter 3.2 out of 5 stars 843 $7.99 Prime HDE IDE/EIDE/PATA Computer to SATA Hard Drive Interface Adapter for PC and Mac If I put the old drive in an external drive case, can I clone from this location versus the internal cable?Thanks. http://www.helpwithpcs.com/upgrading/installing_cd_recorder.htm

How To Connect Ide Dvd Drive To Sata Motherboard

Just search on "IDE to SATA" at Amazon. Clear and accurate, thanks heaps! SHOW ME NOW CNET © CBS Interactive Inc.  /  All Rights Reserved. Note: Users installing an ATA/100 drive: Windows 2000 by default does not support ATA/100 data transfer rates.

Learn More I've focused on readability so I've left out some technical details. In general, the master drive should use the black connector on the end and the slave should use the gray connector in the middle, but if each drive is set either Flag Permalink This was helpful (2) Collapse - Should not be a problem by xpostal / July 22, 2005 1:49 AM PDT In reply to: Mixing SATA and IDE drives in Dvd Drive Power Cable Flag Permalink This was helpful (0) Collapse - Feel free to make a new post.

To its right is the SATA power plug. From a 5.8-inch OLED display, reports of wireless charging and even a 3D scanner for facial recognition, it's all here. In fig 1.3 to the right you can see a standard IDE cable. http://www.osnews.com/story/25660/How_to_Integrate_SATA_and_IDE_Drives When the sleeves are placed over the pins they create an electrical connection.

In single drive configurations, connect the primary drive to the end connector on the 40-pin 80-conductor cable. Ide Hard Drive Jumper Settings Reply Steve on November 13, 2007 at 10:15 am Hi my problem is that my new replacement HD (my old one had a catastrophic failure) does not seem to be recognised or Add to List Sorry, there was a problem. Reply Gwen on February 9, 2009 at 7:18 pm Would like to know the same answer of not format=ting the second (slave) hard drive.

How To Connect Ide Hard Drive To Sata Motherboard

Primary (C:) drive installation during Windows 7 setup: Make sure your drive is detected by your controller or in BIOS during bootup. http://www.dummies.com/computers/pcs/how-to-install-an-internal-cddvd-drive-in-your-computer/ Attaching the SATA cables The next stage is to connect the SATA power and data cables to the device. How To Connect Ide Dvd Drive To Sata Motherboard The first hard drive is SATA, the second which came from an older computer is IDE. How To Connect Dvd Drive To Motherboard Sata and ur write he DIDNT start off with TAKE drive out of box… jeeees….

Please try again now or at a later time. have a peek at these guys I would like to use this computer to recover my data from a Samsung Spin Point (IDE) SV0813H, Hard Disk (XP) and a Seagate U Series 5 (IDE)ST340823A (ME) Hard Disk.How When partitioning and/or formatting a drive, once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Table Of Contents Physical Installation Mounting Your Drive Jumper Settings Reply Dave on November 24, 2008 at 1:34 pm Hi I bought this on Ebay, it works realy well, you can connect any hard drive to a usb socket. How To Install Dvd Drive On Pc

Flag Permalink This was helpful (0) Collapse - Lost half my SATA drive by PennT / July 26, 2005 6:08 PM PDT In reply to: Mixing SATA and IDE drives in For Serial ATA drives (SATA), you don't need to worry about jumpers at all. If you are not replacing a drive then you will need to remove the blank from the computer case at the front of the drive bay where you want the drive. http://internetpasswordpro.com/how-to/how-to-test-if-motherboard-is-bad.html Thanks Reply Hans on November 29, 2008 at 11:38 am Great Article.

Saved me a lot of messing around.Just the right amount of geekiness in my opinion for what it's worth! Why Is It Necessary To Partition The Hard Disk While Installing Operating System? So now the data connects by SATA instead of IDE. One problem though - after setting up the new drive and using Norton Ghost 10.0 to clone the old drive, I can't boot from the new drive.

If you want a single partition (single drive letter), click on Next and your hard drive will be automatically partitioned and formatted as NTFS and Windows 7 will continue installing.

To the left is an example of a typical IDE cable along with a molex power connector. Selection is done by means of a jumper, the option you choose will depend on any other IDE devices you have installed and their respective settings. All clean of course. Sata And Ide Hard Drives Together This was more than Helpfull in my Latest Conquest!!!

Share: PreviousChecking For Spyware Using Netstat NextIs Your Windows XP Now Obsolete? Reply Glenn on November 7, 2007 at 2:59 am Steve - if all is connected then u must format - see above under ‘Software Installation/Cloning'I've just added a second and had Proffitt Forum moderator / July 19, 2005 8:43 AM PDT In reply to: Mixing SATA and IDE drives in a system? this content Deals and Shenanigans Yoyo.com A Happy Place To Shop For Toys Zappos Shoes & Clothing Conditions of UsePrivacy NoticeInterest-Based Ads© 1996-2017, Amazon.com, Inc.

Click on New to add a new partition to the hard drive. I have hooked everything up correctly as you described but when I boot up my computer it freezes on computer screen,when I disconnect the wires and restart it boots up normally?I Select the type of format (NTFS or FAT32).