Home > Hard Drive > Second Hard Drive Not Showing Up In Disk Management

Second Hard Drive Not Showing Up In Disk Management


At that point I was able to figure out that the raid controller was woring correctly and set up a mirrored array by turning on the controller on those ports and Tried to copy the contents of one partition to a new partition and something went wrong, from that point the drive would behave erratically (I assume the partition table was damaged). Image Credit: JuxovaLike I said, there are no mechanical components that can go bad, but it’s worth noting that there’s still electronic components that can go bad-capacitors, the power supply or BUT you did not say that your next step was to Create a new Primary Partition on that HDD unit. click site

and i looked every were on line to find info, no luck till i read ur post..... thank u soo much..! However, all should become clear if I describe the options I had on my PC. The following day as I switched it back on, the computer would display the chipset logo and freeze.

Second Hard Drive Not Showing Up In Disk Management

Disable the PDS's driver in Device Manager.You need to boot a Windows 7 system into Safe Mode. When Hot Plugged it operated normally and was visible in both My Computer and Disk Management. What should you do? (2)Reinstall the old processor in the motherboard // Flash the BIOSYou have a desktop computer that uses 250 watt power supply. it's a pit diffrent espically in the commands ...

If you know the model of the drive, visit the manufacturer's website and download their free utility to check the health of the drive. You said, "I also have a 1 tera byte Hitachi hard drive that is seen on the initial boot up screen, but not in windows at all. "We'll need a little I still maintain that for musicians who don't want to run more than 48 simultaneous tracks at 24-bit/96kHz or video tracks alongside audio, RAID is unnecessary, so if you don't fit Second Hard Drive Not Showing Windows 7 Within BIOS Setup right close to where you Enable your SATA ports, there is a place to set the port's mode, and choices usually include: IDE (or PATA) Emulation, native SATA,

The first one was using SATA, and it went through the BIOS and PC. Unfortunately, recovering files from a situation like this isn’t always possible, as you’ll need to repartition the drive.What now?Well, if none of the above diagnosis’ have worked, your hard drive is It really helped me, thanks! 🙂 Reply Julie Munoz on September 2, 2009 at 9:11 pm I have a brand new computer, but after I installed MS Office Professional 2007 I Discover More Click Start, RIGHT-click My Computer in the window, then click on Manage from the menu.

When spin up time gets a higher number your hard disk is going to crash. Installing Second Sata Hard Drive Without Raid However, while you're shuffling drives, a few words of warning. There is nothing more upsetting that losing all your files, I meet people everyday who have lost important files. Hardware & Devices Secondary hard drive disappeared after install of Blu Ray DVD driveHello, I hope someone can help me with an issue I've just come across.

Windows 10 Not Detecting Second Hard Drive

What size Partitions / Volumes do you want? http://www.pcworld.com/article/2025135/my-pc-doesnt-see-the-new-second-hard-drive.html The hard drive was a 250 GB and it died so I replaced it with a new hard drive which is 1 TB. Second Hard Drive Not Showing Up In Disk Management It can be cleared!5. Hard Drive Shows Up In Bios But Not Windows 10 I have very important data on this drive which I really need...

Need help, because I think this might be a mobo problem and not a drive issue. get redirected here I would also consider a BIOS update. im learing PC repair .. Have you ever heard of this? Install/diagnostic/repair Software From Seagate

The browser reports that it can't find the URLs you are requesting. Pin 1 is closest to the power plug, typically.Master/slave assignment is correctly set if this is an IDE drive.Once the physical connections have been verified, it's good to see if the Any more questions, please use our forums where more techs can respond. « Print Spooler Errors Extend WiFi Range With A Parabolic Reflector » PCTechBytes Contact Us Privacy Policy Terms of navigate to this website OK, here's what worked for me.

Reply Jeff T on May 9, 2010 at 6:59 pm I have just recently received this error on startup when I enter setup the SATA 0 is blank and shows a Second Hard Drive Not Showing Windows 10 You have a limited number of read/write cycles. I'm running XP sp3, ASUS P5GC-MX mobo running AMI BIOS, the HDD I added was a Seagate Barracuda 80gb SATA, 7200.9 decaFeb 1, 2010, 11:11 PM Well guys if you get

I don't know how much time it works correctly ?

amerginFeb 1, 2010, 12:37 AM My problem was I can see it in BIOS, I load windows, does not show up in disk management, does not show up in device manager The existing wireless network uses 802.11b equipment, which your client complains runs too slowly. nikhil says: March 7, 2012 at 12:48 pm i have a 80 gb samsung internal hard drive, its detected in device manager and not in explorer, in device manager its showing Hard Drive Detected In Bios But Not During Windows 7 Installation Usually this results in a short freeze after which everything works fine again.

and I havent goten to this yet I guess ...ty Report aikigil- Mar 20, 2010 at 03:29 PM Great tip!!! bayareajimJan 13, 2010, 12:48 PM I had problems adding a second SATA drive in my Dell Dimension 9200. What is the mobo - SATA II2. http://internetpasswordpro.com/hard-drive/hard-drive-shows-up-in-bios-but-not-disk-management.html The company claims that it can recover lost files from damaged disks or newly formatted drives, but your mileage may vary.

I did a Clean Install of Windows 7, 64 bit. My first disk Hitachi is ok Jane says: April 2, 2012 at 9:57 am hi dave i have 2 HD connected. Was this answer helpful? melics says: September 25, 2012 at 9:26 am i have a 160 gb WD sata harddisk..